Cretex EP [E-Shot]-2-01 Light Grey

Incredibly strong epoxy concrete floor repair (70N/mm2). Withstands virtually any traffic (even to a feather-edge) AND an easy 1:1 mix ratio means no waste!

  • No priming needed
  • Withstands the heaviest traffic
  • Incredibly hard - 70N/mm² compressive strength
  • 1:1 mix – quick and easy with no waste
  • Fast curing in only 6 - 8 hours
  • No smell - non-toxic or taint.
  • Can be trowelled to a feather-edge
  • No cutting out of the edges.
  • No noise, no dust and no mess

Quantity Calculator

Cretex EP [E-Shot]-2-01 Light Grey
2 kg

Regular Price: £39.50

Special Price £30.00


Request Quote
Or call: 0800 980 0852 / 01234 846400



Cretex EP is an incredibly strong epoxy resin concrete floor repair. Holds an ability to withstand virtually any traffic with an easy application on cracked or damaged concrete floors. A twin pack solvent-free resin, Cretex EP achieves the highest adhesion and wear resistance.

Use on: Concrete. For other substances contact Polycote Experts.
Use where: Internal/External
Typical industries: All industries, including food-processing and working environments.
Type of job: Almost any floor repair, due to its incredible strength: Broken steps edges, Spalled/pitted concrete, Raising levels, Impact damage, Bolt holes, creating ramped edges for wheeled traffic, Expansion joint edges
Special features: Heavy duty, chemical resistant, impact resistant, abrasion resistant, can be feather edged, fast curing; cost effective – 1:1 mix means NO waste, non-toxic, non-taint, solvent free, compressive strength many times that of concrete


Pot life:20 mins @ 20oC
Application temperature:10oC - 20oC
Depth of repair (1 layer):Feather edge - 100mm
Mixing ratio:1:1
Initial cure time:6 - 8 hours
Full strength cure time:7 days
Full compressive strength:70N/mm2
Full tensile strength:20N/mm2
Full flexural strength:20N/mm2
Number of parts supplied:2
Coverage:10kg unit - 1.8m2 @ 3mm
Priming required:No

Please consult the technical data sheet for full technical product data.



Thorough substrate preparation is essential.
Remove all loose material – wire brushing is advisable. Sweep clean or vacuum.
The surface must be free from grease, oil or contamination. A gas torch will help to remove oil from the surface. If this is not practical, Polycote Degrease IT may be used to clean the area but this must be thoroughly rinsed off and the substrate dried, before applying Cretex EP.

Important: Thoroughly stir both parts individually before mixing ensuring the resin is evenly dispersed, making sure you get right to the bottom of the container.
Having fully prepared the substrate, simply mix the parts A and B together at a ratio of 1:1 to the quantity required, whether it be a complete unit, or a spoonful for a small repair.
Ensure thorough mixing as an unmixed product will result in a poor or non-cure situation.
Keep all components at room temperature 24 hours before use.

Apply by trowel, or by hand for small isolated areas, wearing suitable protective gloves.
Being resin-rich, Cretex EP has a typically sticky consistency and smoothing may be assisted by wetting the trowel using Polycote Solvent Cleaner as a release agent.
For vertical repairs – where step nosings or expansion joint edges have broken away, the vertical face of the repair material should be supported to prevent slumping.
Suitable sized wooden shuttering should be covered with polythene to reduce adhesion, and should be removed as soon as the material is firm.


Product Questions

No questions yet. Be the first to ask the question!

Customer Reviews

Login, and be the first to review this product

Add a Review

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Please wait...

Product Successfully Added to Your Cart