Polycote Fast Curing Fine Surface Repair Compound


Excellent for filling of fine cracks, holes and surface imperfections. Very strong, cures in only 20 minutes and can be sanded / painted straight away.
  • Extremely tough
  • Cures harder than concrete
  • Very fast curing
  • Ready to paint in only 20 minutes
  • Fantastic adhesion to almost any substrate
  • Solvent free
  • Non-shrink formulation

Quantity Calculator

4 litres

  • Buy 5 for £59.80 each
  • Buy 10 for £57.80 each
  • Buy 20 for £55.80 each

You may also need

Price for all selected : £0.00
  1.    This itemEasi-Fil

Request Quote
Or call: 0800 980 0852 / 01234 846400



Easi-fil is used to fill and smooth out all those unwanted holes, blemishes and cracks. It cures extremely fast and is ready to paint in only 20 minutes.

Use on: Outstanding adhesion to almost any substrate including concrete, brick, wood and metal
Use where:Internal/External
Typical industries:Used across a wide range of commercial and industrial industries
Type of job: For smoothing out fine holes, blemishes and cracks prior to painting
Approximate coverage: 4L unit – 1sqm @ 4mm average thickness
Cure time: 20 mins
Special features: Heavy duty, fast curing, easy single pack application, can be feather edged


Pot life:4 - 5 mins @ 20oC
Application temperature:5oC to - 30oC
Depth of repair (1 layer):Any thickness. It is however designed to fill small areas.
Fully cured strength:Achieved after 20 mins
Number of parts supplied:2
Priming required:No

Please consult the technical data sheet for full technical product data.

View FileEasi-fil Safety Data Sheet    Size: (114.33 KB) View FileEasi-fil Technical Data Sheet    Size: (166.8 KB) View FileEasi-Fill Technisches Datenblatt    Size: (299.6 KB)


Thorough substrate preparation is essential.
Remove all loose / friable material and sweep clean or vacuum.
The surface must be free from grease, oil or any other contaminants. Polycote Degrease IT may be used to clean the area but this must be thoroughly rinsed off.
Please note that the substrate must be COMPLETELY DRY before Easi-fil is applied.

The recommended mixing ratio of filler to hardener is 50:1 by weight. This ratio is not completely critical although the more hardener you add, the faster it will cure and don't forget..., even with the standard mix you only have about 2-3 minutes to apply before it goes rock hard!.
In order to mix the Easi-fil; simply add the hardener (small sachet) to the filler on a mixing board and mix thoroughly. Mix as if spreading it out to prevent air becoming trapped.

Apply the material using a spatula or steel trowel, a smooth finish can be easily achieved. However, when filling 'larger' areas, if the product does need smoothing out after it has cured, this can be achieved with a sander and / or diamond grinder.
Another major benefit of Easi-fil is that it can also be applied to the primer, before application of the top coat. It is often the case that once the priming has been completed that this can make other imperfactions stand out that had been previously missed. Simply repeat the application with the spatula or trowel and then make sure you leave it smooth before applying the top coat.
Finally, another major benefit of Easi-fil is that it has been formulated to accept accept any Polycote top coat without the need of any further primer.


Product Questions

No questions yet. Be the first to ask the question!

Customer Reviews

Login, and be the first to review this product

Add a Review

Other Products You May Need

  • 7 inch Trowel

    7 inch Trowel

    High quality 7 inch trowel
  • 10 inch Trowel

    10 inch Trowel

    Heavy duty 10" trowel
  • Crackfiller EP100

    Crackfiller EP100

    From Only: £38.95
    A pourable ultra low viscosity twin pack epoxy designed to penetrate well into the crack, curing far harder than the original concrete!
  • Degrease IT

    Degrease IT

    From Only: £30.58
    Powerful degreaser for surface preparation – ideal for removal of heavy grease, oils and fats.

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Please wait...

Product Successfully Added to Your Cart