More Views

Easi-Screed External

The ONLY weather resistant self-levelling concrete resurfacer, that will withstand freeze/thaw cycles and stresses of weathering.
  • Excellent for smoothing out worn, ridged or pitted concrete
  • 6mm minimum application thickness
  • Withstands heavy traffic
  • Withstands extreme weather conditions

Quantity Calculator

Easi-Screed External
20 kg

  • Buy 5 for £49.44 each
  • Buy 20 for £45.00 each
  • Buy 50 for £42.00 each
  • Buy 100 for £39.12 each

You may also need

Price for all selected : £0.00
  1.    This itemEasi-Screed External

Request Quote
Or call: 0800 980 0852 / 01234 846400



Easi-Screed External is a highly specialised self-levelling concrete resurfacer designed to cope with the stresses of weathering. Easily applied, it withstands expansion and contraction caused by hot or cold, dry or wet weather conditions.

Use on: Concrete. For other substances contact Polycote Experts.
Use where:External
Approximate coverage: 10 kg unit – 1m2 @ 5mm average thickness
Cure time: Pedestrian traffic – 6 hours @ 20°C
Light wheeled traffic – 24 hours
Heavy duty traffic – 48 hours
Special features: Heavy duty, chemical resistant, impact resistant, abrasion resistant, can be feather edged

Coverage: 2m2 @ 7mm thickness



Pot life:15 mins @ 20oC
Application temperature:5oC - 20oC
Depth of repair (1 layer):5mm - 15mm
Initial curing time (light foot traffic):3 hours @ 20oC
Initial curing time (light foot traffic):24 hours @ 5o
Number of parts supplied:2
Priming required:Concrete or sand and cement screeds – Dampen surface using water. Non-absorbent surfaces – prime with Polycote WD Primer.

Please consult the technical data sheet for full technical product data.

View FileEasi-Fließestrich Außen Technisches Datenblatt    Size: (1.87 MB) View FileEasi-Fließestrich Außen Technisches Datenblatt    Size: (1.87 MB) View FileEasi-Screed External Safety Data Sheet    Size: (161.85 KB) View FileEasi-Screed External Technical Data Sheet    Size: (383.94 KB)


Thorough substrate preparation is essential.
Follow recommendations given on the relevant primer Data Sheet.
See ‘Priming’ below for the primer appropriate to your application.

Concrete or sand and cement screeds – prime with Polycote Easi-Screed Primer.
Non-absorbent surfaces – prime with Polycote WD Primer.
Oily/contaminated surfaces - prime with Polycote OT Primer
Damaged DPM / Rising damp issues - prime with Polycote DPM Primer
Please refer to relevant Data Sheets for preparation and priming methods.

Measure 4.5L of clean water into a suitable sized bucket.
Gradually add the entire 25kg quantity of powder whilst mixing with a heavy duty slow speed drill and mixing paddle. Mixing by hand does not readily give a thoroughly or evenly mixed product.
Mix for at least one minute to allow the additives to dissolve and produce a homogenous mix which should be lump free and a consistency of single cream. When mixed allow to stand for 2 minutes and stir again before application..
Do not mix more than can be applied in 25 minutes. Do not add excess water.

 Pour the material evenly onto the floor to the required thickness and allow the material to start levelling.
The use of depth adjustable floats or a pinned/notched leveller is recommended to assist in spreading the screed to a constant thickness.
A spiked roller should be used immediately over the freshly poured material to eliminate any bubbles trapped within the screed. The next mix of material must be rapidly produced and poured along the wet edge of the material as well as across the exposed floor.
Each application should be laid within 20 minutes of the area adjoining in order to blend evenly into the edge of the previously laid material. This can be helped by gently trowelling along the joint.
Once the workable time has been exceeded it is not possible for the new material to be blended into previously applied material. Therefore the floor topping should be applied to the entire area in one continuous operation.

Application by pump:
 Prior to laying the mixed compound carry out a flow test using a flow ring (30mm diameter x 50mm long). A flow diameter of 135mm + or – 10mm should be achieved, adjust mix accordingly to comply to this flow criteria. Periodically check to ensure mix remains in limit.

1) If the product is not spike rolled immediately and the screed begin to cure, roller spike marks will remain visible. 2) Failure to disperse the air bubbles by spike rolling may result in a lesser impervious finish.
3) Do not add excess water


Product Questions

Hi. Is Easi-screed external product antislipery? On a concrete surface is necessary priming, or just wetting the surface is ok?. Please, let me know. Thanks

Joserra Veiga
Question by: Joserra Veiga on 3 Mar 2016 16:44:00

Easi-Screed external will be slippery when there is any surface liquids on it as it gives you a smooth finish.

If you wish to make this non-slip then apply a coat of Cemcoat Textured over the top.

Answer by: Stuart White (Admin) on 4 Mar 2016 07:20:00
You must be logged in to answer questions.

Customer Reviews

Login, and be the first to review this product

Add a Review

Other Products You May Need

  • Mixing Paddles

    Mixing Paddles

    For thorough and effective mixing of two-part products.
  • Spiked Shoes – Pair

    Spiked Shoes – Pair

    Pair of spiked shoes for use with wet coatings and screeds
  • Spiked Roller

    Spiked Roller

    For spike rolling any of our Cretex or Flortex Screeds such as Easi-screed and Flortex PU Screed. Effectively removes air bubbles.
  • Pin Leveller

    Pin Leveller

    600mm pin leveller for screeding

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Please wait...

Product Successfully Added to Your Cart