More Views

Crackfiller EP100 - Clearance

A pourable ultra low viscosity twin pack epoxy designed to penetrate well into the crack, curing far harder than the original concrete!
  • 2 x 2.5kg Unit Crackfiller EP100 (old stock)

Quantity Calculator

Crackfiller EP100 - Clearance

Regular Price: £78.70

Special Price £60.00

You may also need

Price for all selected : £0.00
  1.      This itemCrackfiller EP100 - Clearance

Request Quote
Or call: 0800 980 0852 / 01234 846400

Details

Details

Crackfiller EP100 is a solvent-free two-part epoxy resin based system with a free flowing formulation designed to penetrate cracks and gaps, rapidly achieving mechanical strength several times that of high quality concrete.

Approx coverage at 3mm x 10mm:

1kg = 33 linear metres

2.5kg = 82.5 linear metres

TIP. You may be interested to note that if the crack is extremely wide or deep, that kiln dried sand (commonly used as block paving sand) can be either poured into the hole first, leaving 5-10mm down from the top) or can be mixed in to the resin to form a type of mortar. Please do remember though that should the crack be thin, it is best to pour the resin neat so that it does indeed penetrate well into the said crack.

IMPORTANT. Is the said crack really a structural crack? If it is irregular and 'wiggly' then it is most probably a structural crack. However, if it is in a dead straight line, then it may well be a 'day joint' (a natural joint between two individually poured slabs of concrete) or even an expansion joint. If it is either of these, it is in fact very important that you fill these joints with a flexible filler, otherwise the concrete is only likely to crack again. If you are not sure perhaps you might light to see one of our very helpful guides on this subject in our expert centre - 'How to tell the difference between an expansion joint and a structural crack'.

Specifications

Specification

Pot life:20 mins @ 20oC
Application room temperature:10oC - 30oC
Application substrate temperature:3oC above dew point
Application humdity:Must not exceed 80%
Initial curing time:4-6 hours
Accepts traffic:12-18 hours
Full cure:7 days
Depth of repair (1 layer):0.1mm - 400mm
Fully cured compressive strength:70N/mm2
Fully cured flexural strength:92N/mm2
Fully cured tensile strength:50N/mm2
Fully cured elastic modulus:3.4KN/mm2
Density:1.12g/cm3
VOC content:Less than 200g/l
Number of parts supplied:2
Priming required:No

Please consult the technical data sheet for full technical product data.

Application

Application

Preparation:
Thorough substrate preparation is essential.
The substrate should be clean and free from dust or oil contamination. For best results the surface should be dry but Crackfiller EP100 will tolerate damp surfaces. A gas torch may help to remove oil or moisture from the surface and clean, dry compressed air may be used to blow out small cracks.


Mixing:
Having fully prepared the substrate, thoroughly stir the contents of Part 'A', then pour all of the hardener Part 'B' into the pot containing resin Part 'A' and mix thoroughly for several minutes using a low speed electric drill until a clear homogenous mix is obtained.
Keep all components at room temperature for 24 hours before use.


Application:
 The materials should be poured into the crack immediately after mixing, using a jug or suitable pouring vessel. A bead of caulk/sealant may be applied temporarily along each side of the crack to prevent the flow of the material onto the surrounding area. Surplus mixed material may generate considerable heat within the container at the end of the pot life. Any unused material is best mixed with sand to reduce the heat output before discarding.

Q&A

Product Questions

No questions yet. Be the first to ask the question!

Customer Reviews

Login, and be the first to review this product

Add a Review

Other Products You May Need

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Please wait...

Product Successfully Added to Your Cart