Cretex Fastset

Cretex Fastset
An incredible fast and strong concrete floor repair. Accepts heavy traffic in 1 hour and cures 3 times stronger than concrete in only 2 hours!
  • High strength, long lasting repair
  • Highly chemical and abrasion resistant
  • Totally impervious
  • Very fast curing in only 1 hour.
  • Non shrink formulation
  • Excellent adhesion
  • Ideal for both internal and external applications

Quantity Calculator

Cretex Fastset
25 kg

  • Buy 5 for £223.90 each
  • Buy 10 for £219.75 each

You may also need

Price for all selected : £0.00
  1.    This itemCretex Fastset

Request Quote
Or call: 0800 980 0852 / 01234 846400



Cretex Fastset is an immensely strong repair mortar which will accept heavy traffic in only 1 hour and cures to over 3 times the strength of concrete in under 2 hours.

Use on: Concrete. For other substances contact Polycote Experts.
Use where: Internal/External
Typical industries: Engineering plants, chemical plants, food factories, breweries
Type of job: Levelling and ramping floors, bonding edging upstands, grouting, bedding ceramic and quarry tiles, waterproof and chemical resistant mortar
Approximate coverage: 25 kg unit – 1m2 @ 15mm average thickness
Cure time: Heavy duty traffic – 1 hour @ 20oC
Special features: Heavy duty, chemical resistant, impact resistant, abrasion resistant, impervious finish


Pot life:10 mins @ 20oC
Application temperature:-20oC to + 35oC
Depth of repair (1 layer):10mm - 50mm
Fully cured strength:55N/mm2
Number of parts supplied:3
Priming required:No

Please consult the technical data sheet for full technical product data.

Safety Data Sheet View FileCretex Fastset Technical Data Sheet    Size: (336.85 KB)


Thorough substrate preparation is essential. Concrete repairs should be prepared with squared off edges having a 10mm minimum vertical lip.
Remove all loose material – wire brushing is advisable. Sweep clean or vacuum.
The surface must be free from grease, oil or contamination.
Ensure concrete is dry (moisture content not exceeding 5%) before priming.
Caution – Cretex Fastset is a methyl methacrylate based resin and has a characteristic odour during the vaporising of the solvent.
Although non-toxic and non-injurious to health, this can cause tainting and OPEN food products should therefore be removed or sealed during and following application until the vapour has dispersed.

The substrate should first be primed with Polycote MC­ Primer, brushing thoroughly into the entire surface.
Once applied, sprinkle 0.5-0.9mm Calcined Bauxite or a suitable kiln-dried quartz aggregate onto the WET PRIMER to provide a mechanical surface key for the material.
Allow the primer to cure, normally within 40 minutes.

Using a clean plastic bucket of at least 25L capacity, add the resin to the powder and mix for 3 minutes using a heavy duty slow speed drill with a 0-15 litre mixing paddle until a homogenous mix is achieved.
Ensure thorough mixing as an unmixed product will result in a poor or non-cure situation.

The material should be placed immediately after mixing.
Trowel out to the required smoothness. DO NOT TAMP as this may cause the resin to rise to the surface leaving a weakened bond at the base of the repair material.
Where the depth of repair requires more than one layer (see 'Application Thickness') MC Primer should be applied between layers to aid inter-section bonding – see 'Priming'.
For vertical repairs – where step nosings or expansion joint edges have broken away, the vertical face of the repair material should be supported to prevent slumping.
Suitable sized wooden shuttering should be covered with polythene to reduce adhesion, and should be removed as soon as the material is firm.


Product Questions

No questions yet. Be the first to ask the question!

Customer Reviews

Login, and be the first to review this product

Add a Review

Other Products You May Need

Please wait...

Product Successfully Added to Your Cart