Easi-Screed Industrial

Easi-Screed Industrial
Tough, fast setting, self levelling floor screed. Super smooth and dust free. Suitable for heavily trafficked industrial applications after only 24hrs
  • Extremely tough
  • Abrasion resistant
  • Incredible 40N/mm compressive strength
  • Fast curing – 2-3 hours for foot traffic
  • Excellent for smoothing out rough / ridged concrete
  • Achieves a non-dusting finish
  • Tough, skid resistant surface

Quantity Calculator

Easi-Screed Industrial
25 kg

£64.85
  • Buy 5 for £59.70 each
  • Buy 20 for £54.92 each
  • Buy 50 for £49.75 each
  • Buy 100 for £45.50 each

You may also need

Price for all selected : £0.00
  1.    This itemEasi-Screed Industrial

Request Quote
Or call: 0800 980 0852 / 01234 846400

Details

Details

Easi-Screed Industrial is a cementitious self-smoothing industrial floor screed containing graded aggregates and acrylic polymer powder. It is excellent for smoothing out worn or ridged concrete and achieves a strong, non-dusting, close tolerance level finish. A 6mm minimum application thickness is required.



Use on: Old or new concrete, quarry and ceramic tiles, vinyl/lino
Use where: Internal
Typical industries: Typical applications include warehouses, factories, workshops, parlours and dairies
Type of job: Used to level uneven (internal) concrete floors and provides a strong finished floor surface. Ideal for rapid installation and curing. Suitable for pumped or hand-mixed operations
Approximate coverage: 25kg – 2m2 @ 7mm thick
Cure time:Foot traffic 2-3 hours
Vehicular traffic 24 hours
Special features:Heavy duty, abrasion resistant, high compressive strength, non-dusting surface, skid resistant finish, can be over-coated with Polycote Flortex SG or Polycote WD Primer after only 24 hours
Specifications

Specification

Pot life:25 mins @ 20oC
Application temperature:10oC to 20oC
Depth of repair (1 layer):Minimum 6mm application
Fully cured strength:1 day - 20N/mm2
7 days - 30N/mm2
28 days - 40N/mm2
Number of parts supplied:1
Priming required:Yes. Use Easi-Screed Primer. Apply the screed when the primer turns clear

Please consult the technical data sheet for full technical product data.

View FileEasi-Fließestrich Industrial Technisches Datenblatt    Size: (223.27 KB) View FileEasi-Screed Industrial Technical Data Sheet    Size: (404.74 KB) View FileEasi-Screed Industrial Safety Data Sheet    Size: (137.98 KB)
Application

Application

Preparation:
Thorough substrate preparation is essential.
Follow recommendations given on the relevant primer Data Sheet.
See ‘Priming’ below for the primer appropriate to your application.


Priming:
Concrete or sand and cement screeds – prime with Polycote Easi-Screed Primer.
Non-absorbent surfaces – prime with Polycote WD Primer.
Oily/contaminated surfaces - prime with Polycote OT Primer
Damaged DPM / Rising damp issues - prime with Polycote DPM Primer
Please refer to relevant Data Sheets for preparation and priming methods.


Mixing:
Measure 4.5L of clean water into a suitable sized bucket. Gradually add the entire 25kg quantity of powder whilst mixing with a heavy duty slow speed drill and mixing paddle.
Mix for at least one minute to allow the additives to dissolve and produce a homogenous mix.
Do not mix more than can be applied in 25 minutes. Do not add excess water.


Starting at the furthest corner from the exit pour the material evenly onto the floor to the required thickness and allow the material to start levelling.
The use of depth adjustable floats or a pinned/notched leveller is recommended to assist in spreading the screed to a constant thickness.
A spiked roller should be used immediately over the freshly poured material to eliminate any bubbles trapped within the screed. The next mix of material must be rapidly produced and poured along the wet edge of the material as well as across the exposed floor.
Each application should be laid within 20 minutes of the area adjoining in order to blend evenly into the edge of the previously laid material. This can be helped by gently trowelling along the joint.
Once the workable time has been exceeded it is not possible for the new material to be blended into previously applied material. Therefore the floor topping should be applied to the entire area in one continuous operation.

Warning:
 1) If the product is not spike rolled immediately and the screed begin to cure, roller spike marks will remain visible 2) Failure to disperse the air bubbles by spike rolling may result in a lesser impervious finish.
3) Do not add excess water

Q&A

Product Questions

No questions yet. Be the first to ask the question!

Customer Reviews

Login, and be the first to review this product

Add a Review

Other Products You May Need

  • Mixing Paddles

    Mixing Paddles

    £18.90
    For thorough and effective mixing of two-part products.
  • Spiked Shoes – Pair

    Spiked Shoes – Pair

    £38.95
    Pair of spiked shoes for use with wet coatings and screeds
  • Spiked Roller

    Spiked Roller

    £44.95
    For spike rolling any of our Cretex or Flortex Screeds such as Easi-screed and Flortex PU Screed. Effectively removes air bubbles.
  • Pin Leveller

    Pin Leveller

    £78.50
    600mm pin leveller for screeding

Please wait...

Product Successfully Added to Your Cart