Our best seller, Flortex Professional is an extremely heavy duty two part 100% solids epoxy concrete floor paint incorporating quality high build fillers, providing a totally impervious coloured gloss finish.
Use Flortex Professional on: Old & new concrete and polymer modified cementitious screeds Use where: Internal Typical industries: Flortex Professional is widely used in warehouses, factories, showrooms, workshops, aircraft hangars and railway depots. It is ideal for use in medical, animal or food environments
Approximate coverage: 15 kg unit - 30- 50m2 depending on profile, porosity and build required Special features: Extremely heavy duty, chemical resistant, impact resistant, abrasion resistant, easily applied by roller, virtually solvent-free, easy clean impervious finish
Pot life: 25 mins @ 20oC Application temperature: 10oC - 25oC Cure time: Re-coat 16-36 hours @ 20oC Light wheeled traffic - 24 hours Full chemical resistance - 7 days Number of parts supplied: 2 Priming required: Prime surfaces with Polycote WD, ZP, DPM, OT or EP Primer
Please consult the Flortex Professional technical data sheet for full technical product data.Flortex Professional Technical Data Sheet Size: (276.94 KB) Flortex Professional Safety Data Sheet Size: (158.54 KB) Flortex Professional Technisches Datenblatt Size: (540.93 KB) Flortex Professional ESH Technisches Datenblatt Size: (190.7 KB)
Thorough substrate preparation is essential.
Recommended methods are:
Powerfloated concrete – use a Vacuum Assisted Shotblaster to remove weak laitance and provide a surface key for the coating. If this is not possible, chemically etch with Polycote Etch IT then rinse thoroughly and allow to dry before applying Flortex Professional.
Loose paint or rust – remove, using a Vacuum Assisted Shotblaster, Floor Grinder or equivalent method.
Loose or friable concrete – use a Vacuum Assisted Shot blaster. If this is not possible, chemically clean with Polycote Etch IT then rinse thoroughly and allow to dry.
Oil or grease – use Hot Compressed Air for large areas of contamination. Smaller, isolated deposits may be chemically cleaned with Polycote Degrease IT, then rinsed thoroughly and allowed to dry.
Prior to application of Flortex® Professional a suitable Polycote primer should be applied, depending on the type and condition of the surface.
Please contact Polycote technical helpline, and prepare the surface in accordance with the appropriate primer data sheet.
Having fully prepared the substrate, stir the individual components before mixing together. As pigment may 'sink', ensure that the mixing is very thorough and from the bottom of the container. Add Part 'B' to Part 'A' and thoroughly mix for at least 3 minutes. For best results use a heavy duty slow speed drill with a mixing paddle.
Ensure thorough mixing as an unmixed product will result in a poor or non-cure situation.
Flortex Professional may be applied by brush, roller or squeegee, depending on the film thickness required.
It is normally applied at a rate of 0.3kg to 0.5kg per 1m2 using a roller or squeegee. When the quantity of resin used exceeds 0.5kg/m2, air bubbles may become trapped within the coating. These are removed using a Polycote Spiked Roller. This must be carried out immediately after application of the resin before curing takes place. Spiked shoes should be worn to avoid disturbing the wet coating.
To achieve a HIGH BUILD or TEXTURED finish – having applied the resin at a rate of 0.5kg to 1.0kg/m2, then gradually sprinkle Kiln Dried Aggregate onto the WET resin at a rate of 2-3kg/m2. The quantity of aggregate required will depend on the thickness of the initial coating. If a textured surface is required, all 'wet spots' must be re-covered with aggregate. Please note: spiked rolling is unnecessary for the first coat when using aggregate. Allow first coat to fully cure (preferably 24 hours) before removing all excess aggregate. A final coat of Flortex® Professional should then be applied using a roller or squeegee. The thickness of this coat may be varied depending on the finish required.
Product QuestionsQuestion by: Abraham Nickson on 20 May 2015 16:04:00
- The coating looks excellent
The coating looks excellent.
I must admit i was very surprised how hard the primer dried and how the top coat covered
- Love the finish
It looks really, really good, love the finish. Im so chuffed
- Wow - Complete transformation
Thank you once again for your assistance during our floor installation, the floor has taken on a new lease of life and we are very grateful
- HGV Workshop - Strong Paint
Polycote can and professionally installed this product for us back in 2014 and it has been excellent. So hard wearing! We had a battery crack and leak acid over the floor and even that didn't cause it to lift. It did however discolour the reason but they assured
- Happy to review
Used this product extensively in our warehouses - over concrete, asphalt and block paving!! It has bonded very well and we are very happy with the floors.
- Happy with the Finish
Very happy with the finish - We used it on a school gym floor.
- Very happy
We applied this onto a new wooden deck, mezz floor and it is still absolutely fine 4 years down the road. It stands up to anything. It takes a lot of scratching