Slip Grip

Slip Grip
Non-slip coating for areas of severe slip hazards. A thickly applied 100% solids resin with tenacious grip.
  • Excellent for individual areas such as high wear ramps, steps on machinery and vehicles, plant and equipment
  • Oil and chemical resistant.

* Required Fields

Reset Options

You may be interested in our 'Bargain Basement' version of this product.

Quantity Calculator

Slip Grip

£237.70

You may also need

Price for all selected : £0.00
  1.    This itemSlip Grip

Details

Details

Polycote Slip Grip – Non-Slip coating for areas of severe slip hazards.

A thickly applied 100% solids resin with tenacious grip. Its coarse anti-slip aggregate provides the top level of slip resistance for areas of severe slip hazards.

Applied as a single coat, which is then completely broadcast with our unrivalled aggregate for an ultra tough, long lasting non-slip surface.

Excellent for those individual areas such as high wear ramps, steps on machinery and vehicles, plant and equipment. Typically used on roads, cycle routes, walkways, traffic calming zones, parking bays etc.

There are two grades available, depending upon time of year: Winter Grade and Summer Grade.



You may be interested in our 'Bargain Basement' version of this product.
Specifications

Specification

Number of parts:2
Pot Life at 20oC:12 mins
Application Temperature:0oC to 35oC
Curing Time at 20oC:40 minutes
Coverage:15kg – 4 - 7.5 sq.m.
30kg – 9 - 15 sq.m.

Please consult the technical data sheet for full technical product data.

View FileSlip Grip Safety Data Sheet    Size: (190.79 KB) View FileSlip Grip Technical Data Sheet    Size: (258.48 KB) View FileSlip Grip - Technisches Datenblatt    Size: (506.53 KB)
Application

Application

Preparation:
Thorough substrate preparation is essential.
All surfaces should be free from all contamination such as de-icing salts, grease or oil, any loose or friable particles, moss or algae growth, dirt and frost.
Grease and oil should be removed using our Polycote Degrease IT.
CONCRETE: Concrete surfaces must be prepared using mechanical preparation; this can be done with a vacuum assisted shotblaster, floor grinder or equivalent method. Please note that water jetting will not key the surface suitably. All repairs should be made prior to application using one of our concrete repair products. We advise that you then prime the surface with one of our Polycote Primers, however this is not essential.
ASPHALT: Again, the surface must be clean, dry and sound. For applications onto asphalt less than 28 days old, atest area should be carried out; this should cover all variations in the asphalt substrate. A circular area of about 100mm in diameter and about 5mm thick should be laid. Once this has cured, its adhesion should be tested with a hammer and bolster; if the product comes up, the asphalt will have to be left until it is 28 days old. The asphalt can be dried using a hot compressed air lance. The surface will not need priming.
STEEL: The steel should be exposed to a bright metal, all rust, dirt, oil, grease and contamination should be removed. The steel should be primed, please contact one of the Polycote technical advisers for the correct product.


Mixing:
Having fully prepared the substrate, stir the resin part thoroughly. Settlement will have occurred during storage and transportation and you should continue mixing until the product has fully homogenised. Add the aggregate and mix until it is totally stirred in. The hardener should now be added and mixed until it has dispersed; this should not take more than 1 minute. For best results use a heavy duty slow speed drill with a mixing paddle. Please note that adding the hardener starts the chemical reaction. Ensure thorough mixing as an unmixed product will result in a poor or non-cure situation.


Application:
The application of Slip Grip is very fast and everything must be ready before you start.
The product should be laid at about 4mm using a serrated squeegee followed by a roller. The roller application should be perpendicular to the squeegee application (crossrolled). A medium pile roller should be used which can be supplied by Polycote UK. Once applied allow to fully cure before trafficking.

Q&A

Product Questions

No questions yet. Be the first to ask the question!

Customer Reviews

Login, and be the first to review this product

Add a Review

Other Products You May Need

Please wait...

Product Successfully Added to Your Cart